Search Results

C20 C21 C22 C23 C24 C25 Features Ethernet converter to RS232/RS485 ESD protection for the RS485 data line Power supply: +12 to +30 VDC Transmission speed up to 115200 bps Tx, Rx and power LED indicators RS485 embedded termination 120 o...

RemoteCOM can be installed on any device from the Redisage C20 - C25 Ethernet Converters family. Features Features Ethernet converter to RS232/RS485 ESD protection for the RS485 data line Power supply: +12 to +30 VDC ...

This page presents capabilities of the Ethernet Converters configuration. First of all, make sure that converter is connected to power supply and to the LAN using a patch cord. If the device has no static IP set up, it will be necessary to obtain its IP addr...

The device can be also configured via the Telnet Console. Firstly, make sure that converter is connected to the power supply and to the LAN using a patch cord. Knowledge of the device’s IP address (default is 192.168.100.100) and Telnet port number (default ...

Another way to configure the device is via a serial console. In case of the C20 - C22 Ethernet Converters an additional USB/UART converter is needed. Service mode Factory reset To restore default settings, type “defaults”. ...

Redisage Configurator is an app used to emulate connection between converter and a PC as if its RS232/RS485 ports would be connected directly to the COM port. The advantage of that functionality is lack of additional cables. Transmission can be tested over E...

How to obtain an IP address of the device? The default static IP address of the device is 192.168.100.100. However, if the DHCP option is set, it will be necessary to obtain the IP address from a local network. First of all, connect the device to the local ...

This article presents a simple instruction of a first connection between a TCP client and a RS232/485 device through the RemoteCOM. Firstly, connect the RemoteCOM according to the diagram below. Then, it is necessary to configure the RemoteCOM’s ports. It...

This article presents a simple instruction of a first connection between a UDP client and a RS232/485 device through the RemoteCOM. Firstly, connect the RemoteCOM according to the diagram below. Then, it is necessary to configure the RemoteCOM’s ports. It...

This article presents a simple instruction of a first connection between a virtual COM port and a RS232/485 device through the RemoteCOM and the Redisage Configurator app. Redisage Configurator is used to emulate connection between converter and a PC as if i...

Features 2-mode Ethernet Modbus Gateway Ethernet converter to RS232/RS485 ESD protection for the RS485 data line Power supply: +12 to +30 VDC Transmission speed up to 115200 bps Tx, Rx and power LED indicators RS485 embedded termination 12...

Modbus Gateway can be installed on any device from Redisage G01 - G03 and G14 - G16 Modbus Gateways family. Features Features 2-mode Ethernet Modbus Gateway ESD protection for the RS485 data line Power supply: +12 to +3...

This page presents capabilities of the Ethernet Converters configuration. First of all, make sure that converter is connected to power supply and to the LAN using a patch cord. If the device has no static IP set up, it will be necessary to obtain its IP addr...

The device can be also configured via the Telnet Console. Firstly, make sure that converter is connected to the power supply and to the LAN using a patch cord. Knowledge of the device’s IP address (default is 192.168.100.100) and Telnet port number (default ...

Another way to configure the device is via a serial console. In case of the G01 - G03 Modbus gateways an additional USB/UART converter is needed. Factory reset To restore default settings, type “defaults”. After that, user...

M-Bus Converters (C01 - C04) C01 C02 C03 C04 Features Serial ports RS232 and RS485 Up to 10 simultaneously connected slave devices ESD protection for the RS232/485 data line 3000 VDC isolation protection Power supply: +12 to +30 VDC or 2...