Commands

Ports configuration commands

In terms of ports configuration it is possible to change parameters like: service, baud rate, data bits, parity, stop bits and so on. UART commands are provided below.

• uart
  • uart help
    Print the help message.
    
    
  • uart list
    List available uarts in the system.
    
    Example:
    uart list
    0: baud: 9600 bits: 8 stop_bits: 1 parity: none (service console)
    1: baud: 115200 bits: 8 stop_bits: 2 parity: odd (covered by cons.)
    2: baud: 9600 bits: 8 stop_bits: 1 parity: none
    3: baud: 1200 bits: 8 stop_bits: 2 parity: even termination: ON (R-COM)
    3: baud: 38400 bits: 8 stop_bits: 2 parity: none termination: OFF
    
    
  • uart PORT_NUMBER baud BAUD
    Set PORT_NUMBER baudrate to BAUD. BAUD value can be one of the following:
    2400, 4800, 9600, 14400, 19200, 38400, 57600, 115200.
    
    Example:
    uart 1 baud 9600
    
    WARNING: UART covered by console. Changes will take place after the reset.
    
    
  • uart PORT_NUMBER bits BITS
    Set bit length to BITS. BITS value can be one only 8.
    
    Example:
    uart 2 bits 8
    
    
  • uart PORT_NUMBER stop_bits STOP_BITS
    Set stop_bits length to STOP_BITS. STOP_BITS value can be only 1 or 2.
    
    Example:
    uart 2 stop_bits 1
    
    
  • uart PORT_NUMBER parity PARITY
    Set uart parity to PARITY. PARITY value can be one of the following: none, odd, even.
    
    Example:
    uart 3 parity even
    
    
  • uart PORT_NUMBER termination STATE
    Set uart termination to new STATE. STATE can be only ON or OFF.
    
    Example:
    uart 3 termination ON
    
    
• uart_service
  • • uart_service help
      Print the help message.
      
      
    • uart_service list
      List of uarts services status.
      
      Example:
      uart_service list
      1 state: ON service: Remote COM port: 1504 enc: YES
      2 state: OFF service: TCP Socket port: 1510
      3 state: OFF service: UDP Socket port: 1510
      
      
    • uart_service UART_NUMBER state STATE
      Set UART_NUMBER state to STATE. STATE value can be only ON or OFF.
      
      Example:
      uart_service 1 state ON
      
      
    • uart_service UART_NUMBER service SERVICE
      Set UART_NUMBER service to SERVICE. SERVICE value can be one of the following: Remote COM, TCP Socket, UDP Socket.
      
      Example:
      uart_service 1 service TCP Socket
      
      
    • uart_service UART_NUMBER port PORT_NUMBER
      Set UART_NUMBER port to PORT_NUMBER. PORT_NUMBER value can be any in the range: 1-65535.
      
      Example:
      uart_service 1 port 1501
      
      
    • uart_service UART_NUMBER enc ENC_STATE
      Set UART_NUMBER encryption to ENC_STATE. ENC_STATE can be only YES or NO.
      
      Example:
      uart_service 1 enc YES
      
      If ENC_STATE is YES then it will ask for a new password for encryption.

Network settings

The following commands might be helpful to change network settings according to target LAN parameters. 

• ipconfig
  • ipconfig addr ADDRESS
    Set IP address to ADDRESS.
    
    Example:
    ipconfig addr 192.168.0.10
    
    
  • ipconfig mask NETMASK
    Set subnet mask to NETMASK (in dot-decimal format).
    
    Example:
    ipconfig mask 255.255.255.0
    
    
  • ipconfig mask BIT_COUNT
    Set subnet mask to BIT_COUNT bits.
    
    Example:
    ipconfig mask 24
    
    
  • ipconfig gateway GATEWAY_IP
    Set network gateway to GATEWAY_IP.
    
    Example:
    ipconfig gateway 192.168.0.1
    
    
  • ipconfig dhcp enable/disable
    Enable or disable DHCP client.
    
    Example:
    ipconfig dhcp enable
    
    
  • ipconfig dns1 ADDRESS
    Set primary DNS to ADDRESS, disable getting DNS from DHCP if enabled.
    
    Example:
    ipconfig dns1 192.168.100.1
    
    
  • ipconfig dns2 ADDRESS
    Set secondary DNS to ADDRESS, disable getting DNS from DHCP if enabled.
    
    Example:
    ipconfig dns2 1.1.1.1
    
    
• eth_mac
  • eth_mac help
    Print the help message.
    
    
  • eth_mac default
    Set device’s MAC address to factory-default one.
    
    
  • eth_mac set MAC_ADDR
    Set device’s MAC address to MAC_ADDR. Accepts both dash and colon-separated formats.
    
    Example:
    eth_mac set 01-02-03-04-05-06
    
    Example:
    eth_mac set 01:02:03:04:05:06
    
    
• http_port
  • http_port help
    Print the help message.
    
    
  • http_port PORT_NUMBER
    Set http port to PORT_NUMBER. A PORT_NUMBER value must be in range: 1-65535.
    
    Example:
    http_port 80
    
    
  • http_port status
    Print current http port.
    
    Example:
    http_port status
    A current http port is 80
    
    
• telnet_port
  • • telnet_port help
      Print the help message.
      
      
    • telnet_port PORT_NUMBER
      Set Telnet port to PORT_NUMBER. A PORT_NUMBER value must be in range: 1-65535.
      
      Example:
      telnet_port 23
      
      

• • • telnet_port status
      Print current Telnet port.
      
      Example:
      telnet_port status
      A current telnet port is 23

Changing username or password

To change username or password, use user command.

Available commands:

• user help
  Print the help message.
  
  
• user mod_name USER_NAME NEW_NAME
  Change the user name to NEW_NAME. It fails if the name is used by another user.
  
  Example:
  user mod_name admin john
  
  
• user passwd USER_NAME
  Change USER_NAME's password.
  
  Example:
  user passwd admin
  ****** <- here is entered password, but '*' appears instead
  
  Note: Everyone can change the password for themselves.