Skip to main content

Data Sheet

Modbus gateways allow data transmission between LAN hosts and serial devices by converting Modbus protocols (Modbus TCP and Modbus RTU/ASCII). They are intended to be used in industrial networks especially in the field of Industry 4.0 but not only. Apart from extending the capabilities of industrial devices, they can be also adapted up to user’s requirements and needs.

Transmission is carried out by two modes: Gateway and Router. In the Gateway mode the port is used to communicate with Slave devices, but in the Router mode with Master devices. It is also possible to set up different modes on every port. Block diagrams below describe how each of these modes works.

d1329031-83b7-4f11-9d1e-5e587ff1085a.png

Features

  • 2-mode Ethernet Modbus Gateway
  • Ethernet converter to RS232/RS485
  • ESD protection for the RS485 data line
  • Power supply: +12 to +30 VDC
  • Transmission speed up to 115200 bps
  • Tx, Rx and power LED indicators
  • RS485 embedded termination 120 ohm
  • Operating temperatures: -40°C to +75°C
  • DIN rail mounting
  • Dimensions: 90x56.4x22.5 mm
  • 3 years warranty
  • Customization of OEM is welcomed

Introduction

Devices are based on G01 - G03 gateways (ESP32 Xtensa LX6 microcontroller) and G14 - G16 gateways (STM32F4 microcontroller) depending on needed ports and interfaces.

Dedicated EMC integrated circuits guarantee improved connection quality by limiting the impact of interference typical for an industrial environment.

Specification

Redisage PN

G01

G02

G03

G14

G15

G16

Ports

RS232

2x

-

-

4x

2x

-

RS485

-

1x

-

-

2x

4x

RS232/RS485

-

-

2x

-

-

-

Microcontroller

ESP32

STM32F4

WiFi

N/A

Power

Voltage

12-30 VDC

Power

< 1 W

Frame ground connection

yes

Baud rate

up to 115200 bps

LED indicators

communication Tx, Rx and power

RS485 termination

120 ohm manually enabled

Connector

RS232/RS485

8 pin terminal block max. 2.5 mm2 wire

Power

3 pin terminal block max. 2.5 mm2 wire

Ethernet

RJ45

Transmission
distance

RS485

max. 1,200 m at 9.6 kbps; max. 400 m at 115.2 kbps
(Belden 9841 2P twisted-pair cable, if different cables are used,
the transmission distance may change)

RS232

max. 15 m at 115.2 kbps

Mounting and enclosure

DIN rail, plastic PA - UL 94 V0, black/green

Temperatures

-40°C to +75°C operating and storage

Humidity

10 - 90% RH, non-condensing

ESD protection

±4 kV contact discharge / ±8 kV air discharge

Certification 

CE, RoHS

Applications

G01 - Ethernet Modbus Gateway 2 x RS232

G02 - Ethernet Modbus Gateway 1 x RS485

G03 - Ethernet Modbus Gateway 2 x RS232/RS485

In the G03 gateway user should use only RS232 or only RS485 interface of one port as they occupy the same internal bus of the device.

G14 - Ethernet Modbus Gateway 4 x RS232

G15 - Ethernet Modbus Gateway 2 x RS232 & 2 x RS485

G16 - Ethernet Modbus Gateway 4 x RS485

Frame ground FG

Electronic circuits are constantly prone to electrostatic discharge ESD.

Redisage Electronics modules feature a design for the frame ground terminal block FG.

The frame ground provides a path for bypassing ESD, which provides enhanced static protection ESD abilities and ensures the module is more reliable.

Connecting FG terminal block to the earth ground will bypass the ESD disturbances outside the device so will provide a better level of protection against ESD.

Frame Ground FG connection reference drawing is provided below.

If earth ground is not availabe FG can be left floating or can be connected with power supply GND.

Pin assignments

G01

7a36a230-516d-413d-a5b2-aeb9c4044bb0.png

G02

27b5fe0a-d8ca-451b-a20d-2f1678d04547.png

G03

54ec2665-7a15-484f-bdf2-6917b054595c.png

G14

3194e998-4094-4387-8062-f44a1ae1bc9d.png

G15

a9bf9b11-bebf-45e5-a3d8-81d001bb0c78.png

G16

1bbc9a2e-ce07-44af-9ad1-3fcfe6685a3b.png

Enclosure dimensions

U Module Enclosure.

98 x 22.5 x 56.4

Units: mm.

983f2bb3-7a16-43af-990d-29e4a7ab679e.png

Getting started

Power supply

Ethernet Modbus gateways G01 - G03 and G14 - G16 have wide voltage power input 12 - 30 VDC. The power consumption is less than 1 W.

LED indicators

Ethernet Modbus gateways G01 - G03 have 3 LED indicators:

  • PW LED Blue - Power
  • ETH LED Green - Network activity 
  • ST LED Orange - USB-UART Serial console mode

38965053-10b3-4e51-be9b-957b01b9938c.png

Ethernet Modbus gateways G14 - G16 have 5 LED indicators:

  • PW LED Blue - Power
  • ER LED Yellow - Error
  • ETH LED Green - Network activity 
  • COM LED Green - RS232/RS485 activity
  • CN LED Yellow - Console mode
  • SR LED Red - Service mode

fd2973ab-76ee-4878-b4ee-4b7626f6cc94.png

Configuration by the Web Page

Default configuration of the Ethernet Modbus gateways:

  • IP address: 192.168.100.100
  • Subnet mask: 255.255.255.0 
  • Gateway: 192.168.100.1
  • DNS 1: 192.168.100.1
  • DNS 2: 8.8.8.8

Default login details:

  • User name: admin
  • Password: admin123

To access to the web page open the web browser, type the IP address in the address bar and log in using the default user name and password. The device and a PC must be connected to the same Local Area Network.

32d29880-42fe-4e1e-93e8-4b857552cbad.png

After successful login, the “Status” page will show the current status of the ports.

4f6ed827-ab6f-4372-8bef-95d723d573c8.png

To change the user name and password click on the user icon and select “Edit user”.

Ports configuration is possible on the “Ports” page.

7b227942-77c0-4f47-84f7-1bddcca0f5be.png

Item

Description

Internal Modbus Address

Internal Modbus Address is qualified by the Gateway/Router as a request for internal resources. The Internal Modbus Address has a higher priority than the Gateway Slave Address.

Idle Time [s]

Determine a time thread waits for the TCP connection. If time expired, the connection and thread are closed. Used only in Gateway Mode.

UART Mode

Gateway

Define the port's role in the system. In the Gateway Mode the port is used to communicate with Modbus Slave.

Router

Define the port's role in the system. In the Router Mode the port is used to communicate with Modbus Master. Note the Routing Configuration section below if the Router Mode is chosen.

Disabled

Disable the port.

UART Protocol

Determine a protocol used for a communication.

Gateway Slaves

Addresses of Modbus Slave Devices connected to Gateway UART ports. Multiple addresses can be written in one field, e.g. 9;11;14-17;80. This field is available only in the Gateway Mode. Use * to select all not assigned addresses.

Slaves Response Timeout [ms]

Specify how long the device will wait for response from Modbus Slave.

Baud Rate

Determine the port's transmission speed over the data channel.

Data Bits

Determine the number of data bits in the port's message frame.

Parity

Enable/disable the parity check in the port's message frame.

Stop Bits

Determine the number of stop bits in the port's message frame.

Termination

Enable/disable termination on RS line.

Routing Slaves

Addresses of Modbus Slaves connected to Modbus Router. Multiple addresses can be written in one field, e.g. 9;11;14-17;80. Use * to select all not assigned addresses.

Slaves Response Timeout [ms]

Specify how long the device will wait for response from Modbus Slave.

IP/Hostname

Determine IP address or Hostname of Modbus Slave.

TCP Port

Determine TCP port of Modbus Slave.

Changing port’s service closes all sockets connected to the ports.

Changing port’s service closes all sockets connected to the ports.

Network settings can be changed on the “Network” page.

8e071700-7429-42f3-83cb-c0560cc74c97.png

Item

Description

Hostname

Label that is assigned to the device.

Configuration Method

Enable/disable the DHCP server. If the DHCP server is disabled, the IP address of the device has to be set manually.

IP Address

IP address of the device.

Netmask

Netmask associated with the IP address.

Gateway

Gateway address currently used by the device.

DNS Address

Domain Name System used by the device.

MAC Settings

Allow setting the default MAC address or typing it manually.

MAC Address

Allow changing the physical address of the device.

HTTP Port

Determine the port of the control panel.

Telnet Port

Allow connection with the device via Telnet.

Modbus TCP Listening Port

Used as an entry point for new Modbus TCP connections.

On the “Device” page there are tools used to a firmware update, a factory reset and a device reboot. There is also basic information about the device.

77484e83-92eb-4f19-88ac-dba66e7d1ed0.png

Item

Description

Firmware Update

Update firmware.

Factory Reset

Restore default ports settings and default network configuration.

Reboot

Reboot the device.

About

Basic information about the device.

Configuration by Serial Console

The device has the ability to be reconfigured via a serial console. In case of the G01 - G03 Modbus gateways an additional USB/UART converter is needed.

  • For G01 - G03 gateways:
    • Turn off the power of the device.
    • Connect Ethernet converter to the dedicated USB/UART converter via microUSB port.
    • Connect the USB/UART converter to the PC.
    • Open the serial console (default baud rate is 115200).
    • Press and hold the S1 button.
    • Turn on the power.
    • Wait until the ST indicator (orange LED) lights up (it should light up after red light - service mode).
    • Release the S1 button.
    • Login using user’s personal credentials or default login details.
    • If the process is successful, configuration command can be typed into the terminal.
  • For G14 - G16 gateways:
    • Install STM32 Virtual COM Port Driver.
    • Turn off the power of the device.
    • Connect Ethernet converter directly to the PC (the dedicated USB/UART converter is not obligatory).
    • Open the serial console (default baud rate is 115200).
    • Press and hold the S1 button.
    • Turn on the power.
    • Wait until the ST indicator (yellow LED) lights up.
    • Release the S1 button.
    • Login using user’s personal credentials or default login details.
    • If the process is successful, configuration command can be typed into the terminal.

Once this is done, log in using the default username and password, then change the network settings using ipconfig command.

a5a95447-11ad-467f-afc0-dd83c392aa44.png

List of all commands

Command

Description

help

Print the help.

conn

Print active TCP connections.

net_stat

Print lwIP statistics.

eth_mac

Print or change MAC address.

ipconfig

Print or change the network configuration.

http_port

Print or change default http port.

telnet_port

Print or change default telnet port.

modbus_tcp_port

Print or change modbus port.

ping

Check internet connection with the desired host.

restart

Restart the system.

user

Print or change user configuration.

sys_heap_usage

Print current heap usage.

modbus

Print or changes modbus settings.

modbus_ports

Print or changes modbus ports settings.

modbus_routing

Print or change modbus routing settings.

exit

Exit console.

Modbus ports configuration commands
  • modbus
    • modbus help
      Print command help.

    • modbus int_addr VALUE
      Set internal Modbus address.

      Example:
      modbus int_addr 5

    • modbus idlet VALUE
      Show or set the idle TIME (in seconds) of the TCP connection after which the TCP connection is terminated by the converter and the TCP socket is released.

      Example:
      modbus idlet 720

      If a subcommand that normally sets a value is not given an argument, it will print the current value.

      Example:
      modbus idlet
      Set idle time is 5000

  • modbus_ports
    • modbus_ports help
      Print command help, does not require com_number.

    • modbus_ports PORT_NUMBER add_slaves [SLAVE_ADDR ;/- SLAVE_ADDR, *]
      Set all addresses of slaves connected to com_port. A star in value means fill rest free slaves. It means all slaves that are not set to other ports will be set to this one.

      Example:
      modbus_ports 1 addslaves 124

      Example:
      modbus_ports 1 addslaves 12-124

      Example:
      modbus_ports 1 addslaves 12;14;18

      Example:
      modbus_ports 1 addslaves 12;14-17;150-200

      Example:
      modbus_ports 1 addslaves 12;14-17;150-200, *

    • modbus_ports PORT_NUMBER show_slaves
      Show addresses of slaves connected to com_port.

      Example:
      modbus_ports 1 showslaves

    • modbus_ports PORT_NUMBER mode [ascii/rtu]
      Set Modbus port mode to ASCII or RTU.

      Example:
      modbus_ports 2 mode ascii

    • modbus_ports PORT_NUMBER baud [RATE]
      Set the baud rate to RATE. For a list of acceptable baud rates, please refer to the manual.

      Example:
      modbus_ports 1 baud 9600

    • modbus_ports PORT_NUMBER bits [CPS]
      Set bit count to C, parity to P, and stop bits to S. Valid values are:
      C: 7, 8 or 9
      P: N, E or O (N- none, E- even, O- odd)
      S: 1 or 2

      Example:
      modbus_ports 1 bits 8N1

      Example:
      modbus_ports 2 bits 7O1

    • modbus_ports PORT_NUMBER state [GATEWAY/ROUTER/DISABLE]
      Enable or disable uart functionality. 

      Example:
      modbus_ports 1 state GATEWAY

      Example:
      modbus_ports 2 state DISABLE

    • modbus_ports PORT_NUMBER termination [on/off]
      Enable or disable termination on RS485 port. 

      Example:
      modbus_ports 1 termination on

    • modbus_ports PORT_NUMBER slave_response_timeout TIMEOUT
      Set response timeout (serial slave) in ms. When this timeout expires, delayed frames are dropped.

      Example:
      modbus_ports 1 slave_response_timeout 2000

      If a subcommand that normally sets a value is not given an argument, it will print the current value.

      Example:
      modbus_ports 2 baud
      Set baud rate is 115200

PORT_NUMBER is a number of ports in modbus gateway and it is counted from 0.

  • modbus_routing
    • modbus_routing help
      Print routing's help.

    • modbus_routing show
      Display all active routing table in system.
      [LP]: [SLAVES NUMBERS] [IP/HOSTNAME] [PORT] [TIMEOUT]

    • modbus_routing add SLAVE_ADDR HOSTNAME PORT TIMEOUT
      SLAVE_ADDR with HOSTNAME PORT is used by uarts working in Modbus router mode. TIMEOUT (in ms) is used to close the connection if a slave is not responding. The maximum records is 8. One record for one address/ip.

      Example:
      modbus_routing add 18 192.168.0.10 502 2000

      Example:
      modbus_routing add 18;25 192.168.0.10 502 2000

      Example:
      modbus_routing add 18-25 192.168.0.10 502 2000

      Example:
      modbus_routing add 18-25;* 192.168.0.10 502 2000

      Example:
      modbus_routing add 18-25 modbus.local 502 2000

    • modbus_routing remove [HOSTNAME_NUMBER/all]
      Remove Modbus Routing Table record. HOSTNAME_NUMBER is line number from /show/ command.

      Example:
      modbus_routing remove 2

      Example:
      modbus_routing remove all
Network settings

The following commands might be helpful to change network settings according to target LAN parameters, 

  • ipconfig
    • ipconfig addr ADDRESS
      Set IP address to ADDRESS.

      Example:
      ipconfig addr 192.168.0.10

    • ipconfig mask NETMASK
      Set subnet mask to NETMASK (in dot-decimal format).

      Example:
      ipconfig mask 255.255.255.0

    • ipconfig mask BIT_COUNT
      Set subnet mask to BIT_COUNT bits.

      Example:
      ipconfig mask 24

    • ipconfig gateway GATEWAY_IP
      Set network gateway to GATEWAY_IP.

      Example:
      ipconfig gateway 192.168.0.1

    • ipconfig dhcp [enable/disable]
      Enable or disable DHCP client.

      Example:
      ipconfig dhcp enable

    • ipconfig dns1 ADDRESS
      Set primary DNS to ADDRESS, disable getting DNS from DHCP if enabled.

      Example:
      ipconfig dns1 192.168.100.1
    • ipconfig dns2 ADDRESS
      Set secondary DNS to ADDRESS, disable getting DNS from DHCP if enabled.

      Example:
      ipconfig dns2 1.1.1.1

  • eth_mac
    • eth_mac help
      Print the help message.

    • eth_mac default
      Set device’s MAC address to factory-default one.

    • eth_mac set MAC_ADDR
      Set device’s MAC address to MAC_ADDR. Accepts both dash and colon-separated formats.

      Example:
      eth_mac set 01-02-03-04-05-06

      Example:
      eth_mac set 01:02:03:04:05:06

  • http_port
    • http_port help
      Print the help message.

    • http_port PORT_NUMBER
      Set http port to PORT_NUMBER. A PORT_NUMBER value must be in range: 1-65535.

      Example:
      http_port 80
    • http_port status
      Print current http port.

      Example:
      http_port status
      A current http port is 80

  • telnet_port
    • telnet_port help
      Print the help message.

    • telnet_port PORT_NUMBER
      Set Telnet port to PORT_NUMBER. A PORT_NUMBER value must be in range: 1-65535.

      Example:
      telnet_port 23
    • telnet_port status
      Print current Telnet port.

      Example:
      telnet_port status
      A current telnet port is 23

  • modbus_tcp_port
    • modbus_tcp_port help
      Print the help message.

    • modbus_tcp_port PORT_NUMBER
      Set http port to PORT_NUMBER. A PORT_NUMBER value must be in range: 1-65535.

      Example:
      modbus_tcp_port 502

    • modbus_tcp_port status
      Print current Modbus port.

      Example:
      modbus_tcp_port status
      A current modbus port is 502
Changing username or password

To change username or password, use user command.

Available commands:

  • user help
    Print the help message.

  • user mod_name USER_NAME NEW_NAME
    Change the user name to NEW_NAME. It fails if the name is used by another user.

    Example:
    user mod_name admin NEW_NAME

  • user passwd USER_NAME
    Change USER_NAME's password.

    Example:
    user passwd admin
    ****** <- here is entered password, but '*' appears instead

    Note: Everyone can change the password for themselves.

Configuration by Telnet Console

Access to the Telnet console can be obtained using a serial terminal program. Configure the connection type to Telnet, enter the IP address and Telnet port number (23 by default).

Console commands are the same as ones described in the serial console section.

0e6873d5-31dd-4050-9c0b-e87fcaa271e4.png

Reset to Factory Defaults

Reset to factory defaults is possible on the web page in the device section or using the service mode. 

Service mode

Procedure to enter service mode for G01 - G03 gateways.

  • Turn off the power of the device.
  • Connect Ethernet converter to the dedicated USB/UART converter via microUSB port.
  • Connect the USB/UART converter to the PC.
  • Open the serial console (default baud rate is 115200).
  • Press and hold the S1 button.
  • Turn on the power.
  • Wait until the ST indicator (red LED) lights up.
  • Release the S1 button.
  • If the process is successful, service commands can be typed into the terminal.

Procedure to enter service mode for G14 - G16 gateways.

  • Install STM32 Virtual COM Port Driver (if it was not done before).
  • Turn off the power of the device.
  • Connect Ethernet converter directly to the PC (the dedicated USB/UART converter is not obligatory).
  • Open the serial console (default baud rate is 115200).
  • Press and hold the S1 button.
  • Turn on the power.
  • Wait until the ST indicator (red LED) lights up.
  • Release the S1 button.
  • If the process is successful, service commands can be typed into the terminal.
List of commands in service mode

Command

Description

help

Print the help.

credits

Print current credits value for this device.

dev_ident

Print the device identification value.

restart

Restart the system.

serial_num

Print the serial number of this device.

version

Display the bootloader version.

xmodem

Download image to the internal Flash using xmodem.

defaults

Reset application variables to defaults.

ipconfig

Print or change the network configuration.

flash_read

Read bytes from flash memory.

md

Read bytes from memory address.

In the service mode, the “ipconfig” command can only show a last static IP address.

Additional notes

Products family sample photo

https://redisage.com

DISCLAMER NOTES
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Datasheet-ID: SR-D